Mercedes-Benz B 250 e 2015 Owner'S Manual Download Page 219

Page: 219 / 293

Problem

Possible causes/consequences and

Solutions

The red brake system

warning lamp is lit while

the drive system is run-

ning. A warning tone also

sounds.

There is insufficient brake fluid in the brake fluid reservoir.

WARNING

Braking efficiency may be impaired.

There is a risk of an accident.

Pull over and stop the vehicle safely as soon as possible, paying

attention to road and traffic conditions. Do not continue driving

under any circumstances.

Safeguard the vehicle against rolling away (

page 145).

Do not top up the brake fluid. Topping up will not rectify the fault.

Consult a qualified specialist workshop.

Observe the additional display messages in the multifunction dis-

play.

! ÷ å

The yellow ABS, ESP

ESP

OFF and brakes

warning lamps are lit

while the drive system is

running.

ABS (Anti-lock Braking System) has been deactivated due to a fault.

Therefore, BAS (Brake Assist), COLLISION PREVENTION ASSIST

PLUS, ESP

(Electronic Stability Program), RBS, PRE

‑

SAFE

, the

HOLD function, hill start assist and the adaptive brake lights, for

example, are also deactivated.

ATTENTION ASSIST is deactivated.

WARNING

The braking performance of the electric motor using recuperative

braking may be either reduced or not effective. If you do not make an

additional effort to apply the brake yourself, the braking effect may not

be sufficient. If necessary, counteract the reduced regenerative brak-

ing effect by applying the brake yourself.

The brake system continues to function normally, but without the

functions listed above. The wheels could therefore lock if you brake

hard, for example.

The steerability and braking characteristics may be severely affected.

The braking distance may increase in an emergency braking situation.
If ESP

is not operational, ESP

is unable to stabilise the vehicle.

There is an increased danger of skidding and risk of an accident.

Observe the additional display messages in the multifunction dis-

play.

Drive on carefully.

Consult a qualified specialist workshop immediately.

If the ABS control unit is malfunctioning, other systems may also not

be available, e.g. the navigation system.

216

Warning and indicator lamps in the instrument cluster

On-board

computer

and

display

Summary of Contents for B 250 e 2015






































































































































































































































































































Search results

Summary of Contents for B 250 e 2015

Reviews:

Related manuals for B 250 e 2015

Brands by name

Popular brands

Mercedes-Benz B 250 e 2015, Owner'S Manual

Search results

Summary of Contents for B 250 e 2015

Reviews:

Related manuals for B 250 e 2015

Brands by name

Popular brands