Mercedes-Benz B 250 e 2015 Owner'S Manual Download Page 41

Page: 41 / 293

Adjust the seat (

page 86).

The seat backrest must be in an almost ver-

tical position.

Pull the seat belt smoothly from belt outlet

Engage seat belt tongue

;

in belt buckle

The seat belt on the driver's seat and the

front-passenger seat may be tightened auto-

matically; see "Belt adjustment"

(

page 38).

If necessary, pull upwards on the shoulder

section of the seat belt to tighten the belt

across your body.

The shoulder section of the seat belt must

always be routed across the centre of the shoul-

der. Adjust the belt outlet if necessary.

To raise: slide the belt outlet upwards.

The belt outlet will engage in various posi-

tions.

To lower: hold belt outlet release

and slide

belt outlet downwards.

Let go of belt outlet release

in the desired

position and make sure that the belt outlet

engages.

Seat belt for the centre rear seat

If the left-hand rear seat backrest is folded down

and back up again, the rear centre seat belt may

lock. The seat belt can then not be pulled out.

To release the rear centre seat belt: pull

the seat belt out approximately 20 mm at the

belt outlet on the backrest and then release it

again.

The seat belt is retracted and released.

Releasing the seat belts

Make sure that the seat belt is fully rolled up.

Otherwise, the seat belt or belt tongue will be

trapped in the door or in the seat mechanism.

This could damage the door, the door trim

panel and the seat belt. Damaged seat belts

can no longer fulfil their protective function

and must be replaced. Visit a qualified spe-

cialist workshop.

Basic illustration

Press release button

, hold belt tongue

;

firmly and guide it back towards belt outlet

Seat belt adjustment

The seat-belt adjustment is an integral part of

the PRE-SAFE

convenience function. This func-

tion adjusts the driver's and front-passenger

seat belt to the upper body of the occupants.

The belt strap is tightened slightly when:

the seat belt tongue is engaged in the belt

buckle and

the ignition is switched on

The seat-belt adjustment will apply a certain

tightening force if any slack is detected between

the vehicle occupant and the seat belt. Do not

hold on to the seat belt tightly while it is adjust-

ing.

You can switch the seat-belt adjustment on and

off in the on-board computer (

page 188).

Occupant safety

Safe

Summary of Contents for B 250 e 2015






































































































































































































































































































Search results

Summary of Contents for B 250 e 2015

Reviews:

Related manuals for B 250 e 2015

Brands by name

Popular brands

Mercedes-Benz B 250 e 2015, Owner'S Manual

Search results

Summary of Contents for B 250 e 2015

Reviews:

Related manuals for B 250 e 2015

Brands by name

Popular brands