Mercedes-Benz B 250 e 2015 Owner'S Manual Download Page 210

Page: 210 / 293

Display messages

Possible causes/consequences and

Solutions

You inadvertently touched the multifunction steering wheel while

steering intervention was active.

While steering intervention is active, make sure not to touch the

multifunction steering wheel.

The vehicle has started to skid and ESP

has intervened.

Use Active Parking Assist again later (

page 158).

Park Assist inoper‐

ative

You have just carried out a large number of turning or parking manoeu-

vres.

Active Parking Assist will become available again after approximately

ten minutes (

page 158).

Pull over and stop the vehicle safely as soon as possible, paying

attention to road and traffic conditions.

Switch off the drive system and start it again.

If the multifunction display still shows the display message:

Consult a qualified specialist workshop.

PARKTRONIC is faulty.

Consult a qualified specialist workshop.

Park Assist

switched off

The vehicle is parked. A warning tone also sounds.

The display message disappears automatically.

Traffic

Traffic Sign

Sign Assist

Assist

currently unavaila‐

ble

ble See

See Owner's

Owner's Man‐

Man‐

ual

Traffic Sign Assist is temporarily inoperative.

Possible causes:

the windscreen is dirty in the camera's field of vision

visibility is impaired due to heavy rain, snow or fog

Clean the windscreen.

If the system detects that the camera is fully operational, the display

message disappears.

Traffic Sign Assist is operational again.

Traffic

Traffic Sign

Sign Assist

Assist

inoperative

Traffic Sign Assist is faulty.

Consult a qualified specialist workshop.

Cruise control and

SPEEDTRONIC inoper‐

ative

SPEEDTRONIC and cruise control are malfunctioning.

A warning tone also sounds.

Consult a qualified specialist workshop.

Display messages

207

-b

oar

comp

lay

Summary of Contents for B 250 e 2015






































































































































































































































































































Search results

Summary of Contents for B 250 e 2015

Reviews:

Related manuals for B 250 e 2015

Brands by name

Popular brands

Mercedes-Benz B 250 e 2015, Owner'S Manual

Search results

Summary of Contents for B 250 e 2015

Reviews:

Related manuals for B 250 e 2015

Brands by name

Popular brands