Mercedes-Benz B 250 e 2015 Owner'S Manual Download Page 59

Page: 59 / 293

Suitability of the seats for attaching a belt-secured child restraint system

If you use a baby car seat of category 0 or 0+ or a rearward-facing child restraint system of category

I on a rear seat, you must adjust the driver's or front-passenger seat so that the seat does not touch

the child restraint system.

If you use a category I, forward-facing child restraint system, you should remove the head restraint

of the respective seat (

page 90), if possible. The backrest of the child restraint system must, as

far as possible, lie flat against the backrest of the seat.

Always observe the notes in the "Child restraint system" section (

page 49) and the child restraint

system manufacturer's installation instructions.

When you remove the child restraint system you must replace the head restraints again immediately

(

page 89). All vehicle occupants must adjust their head restraints correctly before beginning the

journey.

Legend for the table:
X Seat which is unsuitable for children in this weight category.

U Suitable for child restraint systems in the "Universal" category that are approved for use in this

weight category.

UF Suitable for forward-facing child restraint systems that belong to the "Universal" category and

are approved for use in this weight category.

L Suitable for child restraint systems as recommended; see the "Recommended child restraint

systems" table (

page 58). Suitable for semi-universal child restraint systems if the vehicle

and the seat are listed in the child restraint system manufacturer's vehicle model list.

Front-passenger seat

Weight category

Front-passenger

front airbag enabled

The front-passenger

front airbag is disa-

bled

up to 10 kg

, L

up to 13 kg

, L

9 kg to 18 kg

UF, L

, L

UF, L

15 kg to 25 kg

UF, L

III

22 kg to 36 kg

UF, L

Rear seats

Weight category

Left, right

Centre

up to 10 kg

U, L

, L

up to 13 kg

U, L

, L

9 kg to 18 kg

U, L

, L

15 kg to 25 kg

U, L

III

22 kg to 36 kg

U, L

The vehicle is equipped with an automatic front-passenger front airbag deactivation system. The PASSENGER

AIR BAG OFF indicator lamp must be lit.

Child restraint systems with a supporting bracket are not suitable for this seat.

Children in the vehicle

Saf

ety

Summary of Contents for B 250 e 2015






































































































































































































































































































Search results

Summary of Contents for B 250 e 2015

Reviews:

Related manuals for B 250 e 2015

Brands by name

Popular brands

Mercedes-Benz B 250 e 2015, Owner'S Manual

Search results

Summary of Contents for B 250 e 2015

Reviews:

Related manuals for B 250 e 2015

Brands by name

Popular brands