MDT Technologies SCN-IP000.03 Technical Manual Download Page 55

Page: 55 / 57

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

7 Index

7.1 Register of illustrations

Figure 1: Structure – Hardware module

.................................................................................................. 6

Figure 2: IP Router as line coupler

........................................................................................................ 10

Figure 3: IP Router as area coupler

....................................................................................................... 11

Figure 4: IP Router as area- and line coupler

........................................................................................ 12

Figure 5: Installation example

............................................................................................................... 13

Figure 6: Commissioning Password/ Authentication Code

................................................................... 15

Figure 7: Secure Commissioning/Secure Tunneling

............................................................................. 16

Figure 8: Enter FDSK

............................................................................................................................ 17

Figure 9: Subsequent input FDSK

......................................................................................................... 18

Figure 10: General Settings – IP Router

................................................................................................ 20

Figure 11: Device – Settings

................................................................................................................. 22

Figure 12: Device – IP Settings

............................................................................................................. 23

Figure 13: General Settings (without Secure)

....................................................................................... 24

Figure 14: Settings – IP Configuration (without Secure)

...................................................................... 25

Figure 15: Settings – KNX Multicast Address

...................................................................................... 27

Figure 16: Settings – Main line

............................................................................................................. 28

Figure 17: Settings – Sub line

............................................................................................................... 30

Figure 18: Settings ETS4 – Communication

......................................................................................... 32

Figure 19: Settings ETS4 – Discovered connections

............................................................................ 32

Figure 20: ETS4 – Local Interface Settings

.......................................................................................... 33

Figure 21: ETS5 - Bus - Interfaces

........................................................................................................ 34

Figure 22: ETS5 - Discovered connections

........................................................................................... 34

Figure 23: ETS5 – IP Tunneling connection

......................................................................................... 34

Figure 24: Set Tunneling Addresses (without Secure)

.......................................................................... 35

Figure 25: Set Tunneling Addresses in ETS5 (with Secure)

................................................................. 36

Figure 26: Set Tunneling Address ETS5 – Properties

........................................................................... 36

Figure 27: General settings – E-Mail Client

.......................................................................................... 37

Figure 28: Settings – Web Interface

...................................................................................................... 38

Figure 29: Settings – Time/Date

............................................................................................................ 39

Figure 30: Settings – Status elements

.................................................................................................... 40

Figure 31: Settings – Bit Alarm

............................................................................................................ 42

Figure 32: Settings – Text Alarm

.......................................................................................................... 44

Figure 33: Settings – Status report

........................................................................................................ 45

Figure 34: Secured group address

......................................................................................................... 48

Figure 35: Changing the security settings for the group address

.......................................................... 48

Figure 36: Web-Interface – Example IP Configuration

........................................................................ 49

Figure 37: Web Interface – Login window

........................................................................................... 50

Figure 38: Web Interface – Destination E-Mail test

.............................................................................. 51

Figure 39: Web Interface – E-Mail settings

.......................................................................................... 51

Figure 40: Example 1 – Server data (German)

...................................................................................... 52

Figure 41: Example 2 – Server data (German)

...................................................................................... 52

Figure 42: Web Interface – Destination E-Mail Test

............................................................................ 53

Summary of Contents for SCN-IP000.03


























































Search results

Summary of Contents for SCN-IP000.03

Reviews:

Related manuals for SCN-IP000.03

Brands by name

Popular brands

MDT Technologies SCN-IP000.03, Technical Manual

Search results

Summary of Contents for SCN-IP000.03

Reviews:

Related manuals for SCN-IP000.03

Brands by name

Popular brands