MDT Technologies SCN-IP000.03 Technical Manual Download Page 38 | Manualshive

Page: 38 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

38

38

5.1.2 Web Interface

The following settings are available to set-up the web interface:

Figure 28: Settings – Web Interface

Password

The password is used to control access to the Web Interface. There should always be a password be
entered!

Timeout for valid login

The parameter specifies the time at which the web interface can be reached after a login. After the
set time, the web interface is automatically locked.

Timeout startup of the web interface after reset

The parameter specifies the time how long the web interface can be reached after restarting
(switching ON the bus voltage or reset via ETS). After the set time, the Web interface is no more
accessible and can only be reached after a restart or after an activation of the web interface via
object.

Temporary activation of the web interface for Email event

The parameter allows the temporal activation of the web interface after sending an email.

Activation/deactivation of the web interface over object

To activate via bus, regardless of any other settings, a communication object can be displayed to
activate the web interface via object.

Following communication object appears for this purpose:

Number

Name

Length

Usage

55

Web interface

1 Bit

lock/unlock of Web Interface

Table 8: Communication object – lock/unlock Web-Interface

Attention:

For security reasons it is recommended to disable the web interface after a certain time

using the parameter "Timeout startup of the web interface after reset" or to activate the web
interface only via object and deactivate when not in use!

«
...
36
37
38
39
40
...
»

Summary of Contents for SCN-IP000.03


























































Reviews:

No comments

Related manuals for SCN-IP000.03

Brand: Xantrex Pages: 8

Brand: Patton electronics Pages: 8

Brand: ICP DAS USA Pages: 14

Brand: ICP DAS USA Pages: 25

Brand: ICP DAS USA Pages: 15

Brand: ICP Pages: 14

Brand: Zonet Pages: 8

Ethernet Communication Module DVPEN01-SL

Brand: Delta Electronics Pages: 54

Brand: Axis Pages: 104

Brand: Davey Pages: 18

Brand: Campbell Pages: 38

RealPort Ethernet 10/100

Brand: Xircom Pages: 30

Brand: Tektronix Pages: 178

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

Brand: TRENDnet Pages: 62

Brand: Ravpower Pages: 27

Brand: Juniper Pages: 2

TeleCLIENT TC7730 Series

Brand: ETL Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands