MDT Technologies SCN-IP000.03 Technical Manual Download Page 28 | Manualshive

Page: 28 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

28

28

4.5 Main line

The following parameters can be set in the submenu "Main line":

Figure 16: Settings – Main line

The table shows the setting ranges for the individual parameters:
ETS-Text

Dynamic Range

[Default value]

Comment

Configuration



groups: filter
physical: block



groups, physical: filter



groups: route
physical: filter



groups, physical: route



configure

Setting the filtering of telegrams on the
main line

Group telegrams



transmit all



block



filter

Defining the treatment of group
telegrams

Main group telegrams 14/15



transmit all



block



filter

Defining the treatment of group
telegrams of the main lines 14 and 15

Physical telegrams



transmit all



block



filter

Defining how physically addressed
telegrams are to be treated

Table 6: Settings – Main line

If the "configure" parameter is active for the "Configuration", the following parameters are freely
adjustable.
For all other "Configuration", the parameters for "Group telegrams, Main group telegrams 14/15 and
Physical telegrams" are set to fixed values - according to the setting.

«
...
26
27
28
29
30
...
»

Summary of Contents for SCN-IP000.03


























































Reviews:

No comments

Related manuals for SCN-IP000.03

Brand: Makita Pages: 2

Brand: Hawking Pages: 2

Brand: NetComm Pages: 69

Brand: Talent Pages: 18

Brand: Tripp Lite Pages: 2

Wisenet PRN-6400DB4

Brand: Hanwha Techwin Pages: 125

Brand: Draytek Pages: 17

Brand: ExtraHop Pages: 3

Brand: Hypercom Pages: 2

Elinx EIRP410-2SFP-T

Brand: B&B Electronics Pages: 24

Full-Rated Router ADSL2+

Brand: PC Concepts Pages: 104

Brand: Me Pages: 28

SA-REP-ETHERLINK_II-1DA-PL

Brand: S-Access Pages: 106

Brand: Allied Telesis Pages: 2

Brand: Proxim Pages: 89

Brand: Accusys Pages: 12

Brand: Zte Pages: 28

Network Expansion Port 2

Brand: Navico Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands