MDT Technologies SCN-IP000.03 Technical Manual Download Page 13 | Manualshive

Page: 13 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

13

13

2.8.4 Bus access function (KNXnet/IP Tunneling)

The KNX IP Router can be used as an interface to KNX. It can be accessed from anywhere on the LAN
to the KNX. Therefore a second physical address has to be allocated. This is described in more detail
in the following chapters.

2.8.5 Installation - Example

The following figure shows the exemplary structure of a network with two IP Routers used in each
case as an area coupler:

Figure 5: Installation example

«
...
11
12
13
14
15
...
»

Summary of Contents for SCN-IP000.03


























































Reviews:

No comments

Related manuals for SCN-IP000.03

Brand: D-Link Pages: 10

Adapter Bracket

Brand: Paradyne Pages: 1

Brand: Draytek Pages: 8

Brand: Supermicro Pages: 24

Brand: XMOS Pages: 6

Brand: Hamlet Pages: 122

Brand: ZyXEL Communications Pages: 12

TEG-S16R - DATA SHEETS

Brand: TRENDnet Pages: 12

CONNECT Box Pro

Brand: ratiotec Pages: 12

Magnum mP62-5V -1M1SSC

Brand: GarrettCom Pages: 40

Brand: LAWO Pages: 68

Brand: Craftsman Pages: 28

Brand: Huawei Pages: 260

Brand: Huawei Pages: 2

Brand: Huawei Pages: 70

Brand: Huawei Pages: 51

Brand: Huawei Pages: 92

Brand: Huawei Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands