MDT Technologies SCN-IP000.03 Technical Manual Download Page 56

Page: 56 / 57

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

7.2 List of tables

Table 1: Overview LEDs

......................................................................................................................... 7

Table 2: General Settings – IP Router

................................................................................................... 21

Table 3: General Settings (without Secure)

........................................................................................... 24

Table 4: Settings – IP Configuration (without Secure)

......................................................................... 25

Table 5: Settings – KNX Multicast Address

......................................................................................... 27

Table 6: Settings – Main line

................................................................................................................ 28

Table 7: Settings – Sub line

................................................................................................................... 31

Table 8: Communication object – lock/unlock Web-Interface

............................................................. 38

Table 9: Communication objects – Time/Date

...................................................................................... 39

Table 10: Status elements – 1 Bit

.......................................................................................................... 40

Table 11: Status elements – 1 Byte

....................................................................................................... 41

Table 12: Status elements – 2 Byte

....................................................................................................... 41

Table 13: Status elements – 4 Byte

....................................................................................................... 41

Table 14: Status elements – 14 Byte

..................................................................................................... 41

Table 15: Communication objects – Status elements

............................................................................ 41

Table 16: Setting options – Bit Alarm

................................................................................................... 42

Table 17: Communication objects – Bit Alarm

..................................................................................... 42

Table 18: Settings – Text Alarm

........................................................................................................... 44

Table 19: Communication objects – Text Alarm

.................................................................................. 44

Table 20: Settings – Status report

.......................................................................................................... 45

Table 21: Communication objects – Status report

................................................................................. 45

Table 22: Communication object – NTP Time Server Error

................................................................. 46

Table 23: Communication object – E-mail Error code

.......................................................................... 46

Table 24: Communication object – E-mail buffer

................................................................................. 46

Table 25: Overview – Communication objects

..................................................................................... 47

Summary of Contents for SCN-IP000.03


























































Search results

Summary of Contents for SCN-IP000.03

Reviews:

Related manuals for SCN-IP000.03

Brands by name

Popular brands

MDT Technologies SCN-IP000.03, Technical Manual

Search results

Summary of Contents for SCN-IP000.03

Reviews:

Related manuals for SCN-IP000.03

Brands by name

Popular brands