MDT Technologies SCN-IP000.03 Technical Manual Download Page 30

Page: 30 / 57

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

4.6 Sub line

The following parameters can be set in the submenu "sub line":

Figure 17: Settings – Sub line

The table shows the setting ranges for the individual parameters:
ETS-Text

Dynamic Range

[Default value]

Comment

Configuration



groups: filter
physical: block



groups, physical: filter



groups: route
physical: filter



groups, physical: route



configure

Setting the filtering of telegrams on
the sub line

Group telegrams



transmit all



block



filter

Defining the treatment of group
telegrams of groups 0-31, except the
groups 14/15

Sub group telegrams 14/15



transmit all



block



filter

Defining the treatment of group
telegrams of main groups 14 and 15

Physical telegrams



transmit all



block



filter

Defining how physically addressed
telegrams are to be treated

Physical: Repetition if errors
on sub line



normal



reduced

Defining whether the message is to
be repeated in case of failure

Group: Repetition if errors
on sub line



normal



reduced

Defining whether the message is to
be repeated in case of failure

Summary of Contents for SCN-IP000.03


























































Search results

Summary of Contents for SCN-IP000.03

Reviews:

Related manuals for SCN-IP000.03

Brands by name

Popular brands

MDT Technologies SCN-IP000.03, Technical Manual

Search results

Summary of Contents for SCN-IP000.03

Reviews:

Related manuals for SCN-IP000.03

Brands by name

Popular brands