MDT Technologies SCN-IP000.03 Technical Manual Download Page 22 | Manualshive

Page: 22 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

22

22

4.1.2 Device – Settings

The following picture shows the settings of the IP interface:

Figure 11: Device – Settings

Name

The name describes, among other things, how the connection is displayed in the ETS. Any name with
a maximum length of 50 characters can be entered.

Secure commissioning

Activation/deactivation of Secure Commissioning. If a device is not commissioned safely, the secure
functions are deactivated, see also “3 Safety – IP Secure/Data Secure”

Secure Tunneling

Activation/deactivation of Secure Tunneling. If Secure Tunneling is activated, the communication via
the tunneling connection is encrypted, see also “3 Safety – IP Secure/Data Secure”

«
...
20
21
22
23
24
...
»

Summary of Contents for SCN-IP000.03


























































Reviews:

No comments

Related manuals for SCN-IP000.03

Brand: 3Com Pages: 48

Brand: BandLuxe Pages: 67

Brand: Vanguard Pages: 4

Brand: Ravpower Pages: 27

Brand: IMC Networks Pages: 36

Brand: Intel Pages: 958

SUPERSERVER 6027TR-H71FRF

Brand: Supero Pages: 118

Brand: Xyclop Pages: 144

Brand: Silvertel Pages: 9

iMarc SLV 9820-2M

Brand: Paradyne Pages: 24

Brand: Lanner Pages: 141

Service Aggregation Router 7705

Brand: Alcatel-Lucent Pages: 20

Brand: AIC Pages: 64

CamCon FCS-4000

Brand: LevelOne Pages: 94

DynaStar DS2000-IFR

Brand: GarrettCom Pages: 40

Turbo 16/4 Token-Ring PC Card 2

Brand: IBM Pages: 123

Brand: Waveshare Pages: 27

Brand: Waveshare Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands