MDT Technologies SCN-IP000.03 Technical Manual Download Page 57 | Manualshive

Page: 57 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

57

57

8 Attachment

8.1 Statutory requirements

The above-described devices must not be used with devices, which serve directly or indirectly the
purpose of human, health- or lifesaving. Further the devices must not be used if their usage can
occur danger for humans, animals or material assets.
Do not let the packaging lying around careless, plastic foil/ -bags etc. can be a dangerous toy for kids.

8.2 Disposal routine

Do not throw the waste equipment in the household rubbish. The device contains electrical devices,
which must be disposed as electronic scrap. The casing contains of recyclable synthetic material.

8.3 Assemblage

Danger to life due to electric current!

All activities on the device should only be done by an electrical specialist. The county specific
regulations and the applicable KNX-directives have to be observed.

8.4 History

V1.0 - First Version of the 3rd generation of IP Interfaces – SCN-IP000.03

05/2019

V1.1 - General corrections; descriptions "Update", "Reset" extended

12/2020

«
...
55
56
57

Summary of Contents for SCN-IP000.03


























































Reviews:

No comments

Related manuals for SCN-IP000.03

Brand: iDirect Pages: 60

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 23

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Brand: D-Link Pages: 53

ADSL/ADSL2/ADSL2+ Router 660R-6xC Series

Brand: ZyXEL Communications Pages: 282

Wisenet PRN-6400B4

Brand: Hanwha Techwin Pages: 14

System Storage DS3200

Brand: IBM Pages: 2

LMP-1202G-SFP Series

Brand: ANTAIRA Pages: 19

Brand: Alarm Pages: 5

FiberTwist G6426

Brand: Genexis Pages: 9

Edge-Core A07-ES4548C

Brand: Atlantis Land Pages: 2

Brand: ZyXEL Communications Pages: 12

TeleLite 720920 Series

Brand: Positron Pages: 21

Brand: Juniper Pages: 230

Brand: Netstor Pages: 17

Broadband Wireless Router None

Brand: Olicom Pages: 5

Brand: Tripp Lite Pages: 2

CloudVision DCA-CV-100

Brand: Arista Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands