manualshive.com logo in svg

Masimo Root, Operator'S Manual, Page: 74 / 152

Share
Download
Masimo Root Operator'S Manual Download Page 74

Root   

Chapter 3: Operation 

 

www.masimo.com 

72 

  Masimo   

 

Standby Mode 

Standby Mode allows for patient monitoring to be temporarily suspended. The Standby icon 

(see image below) is located in the top-left corner of the screen. 

To enable Standby Mode (suspend monitoring) 

1.

 

On Root, open the 

Access Control

 menu. 

2.

 

Swipe the 

standby enabled

 button to 

ON

. Return to the home screen on Root, and 

the Standby icon will appear on the screen in the top-left corner

.

 

3.

 

Press the Standby icon, and a notification message will appear on the screen 

indicating that monitoring is suspended (see image below). 

To exit Standby Mode (resume monitoring)   

•

 

Tap anywhere on the screen. 

WARNING:

 When Root is in Standby Mode, monitoring is suspended and no alarms will be 

active, with the exception of the low battery alarm.   

Note:

 Standby Mode will not affect any devices using Root's Iris Connectivity to Masimo 

Patient SafetyNet. 
 

 

 

Summary of Contents for Root

























































































































































Reviews:

No comments