manualshive.com logo in svg

Masimo Root, Operator'S Manual, Page: 110 / 152

Share
Download
Masimo Root Operator'S Manual Download Page 110

Root   

Chapter 9: Iris 

 

www.masimo.com 

108 

  Masimo   

 

Iris Status Screen 

Information about Iris Connectivity Ports are displayed on this screen, which is accessible by 

selecting the Iris option on the Main Menu. 

 

 

Connection 

Status Color 

Description of Connection   

Green 

Standalone device is successfully connected to Root, and Root is 

successfully connected to a Patient SafetyNet or Connectivity Gateway. 

Yellow 

Standalone device is successfully connected to Root; however, Root is not 

successfully connected to a Patient SafetyNet or Connectivity Gateway. 

Gray 

No standalone device is connected to the Iris Connectivity Port. 

 

Additionally, the Ports are also mapped to the Iris icon on the Status Bar. When a standalone 

device is connected to Root via one of the Ports, the corresponding part of the icon will be lit 

green or yellow. In the example below, a standalone device is connected to Iris Connectivity 

Port 1. 

Port 1 (connected) 

 

Port 2 

Port 3 

Port 4 

Status and connection type are read-only and not configurable by the user. For more 

information on Iris connectivity, see Instructions for Use or Operator’s Manual for the 

appropriate version of Masimo Patient SafetyNet. 

 

Summary of Contents for Root

























































































































































Reviews:

No comments