manualshive.com logo in svg

Masimo Root, Operator'S Manual, Page: 139 / 152

Share
Download
Masimo Root Operator'S Manual Download Page 139

Root   

Chapter 13: Service and Maintenance 

 

www.masimo.com 

137 

  Masimo   

 

 

NIBP Air Leak Test 

Note:

 This section is provided as a reference and intended for qualified service professionals 

only. 

Pass Criteria

 

International standards for automated NIBP devices require that air leakage within the 

pneumatic system must not exceed 6mmHg/minute. 

 

Procedure

 

1.

 

Connect the manometer and rigid volume (500 mL bottle) to the air hose 

connection using "T" adapters and connection tubing. 

2.

 

Touch the "Test" button on the display to start the test. 

3.

 

Wait for the countdown timer to reach 0 second. 

4.

 

Check the "Result" section, if the leak rate is greater than 6 mmHg/min, contact 

customer service. 

 

Zero Point Calibration 

Note

: This section is provided as a reference and intended for qualified service professionals 

only. 

Calibration Steps

 

1.

 

Enter NIBP menu, select "Calibration", and select Zero Point Calibration.   

2.

 

Connect a manometer, volume and the hand bulb to the Module using "T" adapters 

and connection tubing. 

3.

 

Apply 0 (zero) mmHg to the module. 

4.

 

Touch the "Calibrate" to start the zero point calibration. 

5.

 

Results are displayed for Zero Point Calibration. 

6.

 

Calibration is completed. 

 

Span Point Calibration 

Note:

 This section is provided as a reference and intended for qualified service professionals 

only. 

Calibration Steps

 

1.

 

Enter NIBP menu, select "Calibration", and select Span Point Calibration.   

2.

 

Connect a manometer, volume and the hand bulb to the Module using "T" adapters 

and connection tubing. 

3.

 

Apply 250 mmHg to the module. 

4.

 

Touch the "Calibrate" to start the span point calibration. 

5.

 

Results are displayed for Span Point Calibration. 

6.

 

Calibration is completed. 

 

Summary of Contents for Root

























































































































































Reviews:

No comments