manualshive.com logo in svg

Masimo Root, Operator'S Manual, Page: 69 / 152

Share
Download
Masimo Root Operator'S Manual Download Page 69

Root   

Chapter 3: Operation 

 

www.masimo.com 

67 

  Masimo   

 

 

Intervals for NIBP 

 

From the 

NIBP

 screen, touch 

Intervals

, and then change any of the following options: 

Options

 

Description

 

Factory 

Default 

Settings

 

User Configurable 

Settings

 

Set Mode  The mode of measurement for NIBP. 

Manual 

Manual, Automatic, Stat 

Interval 

Note

: Option available when 

Automatic 

mode is selected. 

Automatic interval measurement 

mode will take blood pressure 

measurements once every desired 

interval. 

15 min 

2 min, 3 min, 4 min, 5 min, 

10 min, 15 min, 30 min, 

60 min, 90 min 

Stat 

Duration 

Note

: Option available when 

Stat 

mode is selected. 
Stat interval measurement mode will 

take blood pressure measurements 

continuously for the desired duration. 

10 min 

5 min, 10 min 

 

Calibration for NIBP 

 

The 

Calibration 

option on the 

NIBP 

menu allows a qualified service professional to access 

calibration settings and tools for the NIBP module. For more information, see 

Chapter 13: 

Service and Maintenance

 on page 135. 

Note:

 This section is provided as a reference and intended for qualified service professionals 

only. 

 

Summary of Contents for Root

























































































































































Reviews:

No comments