manualshive.com logo in svg

Masimo Root, Operator'S Manual, Page: 117 / 152

Share
Download
Masimo Root Operator'S Manual Download Page 117

 

www.masimo.com 

115 

  Masimo   

 

Chapter 11: Troubleshooting 

Troubleshooting Radical-7, Radius-7, and MOC-9 Modules 

For information on troubleshooting values that are provided from Radical-7, Radius-7, and 

MOC-9 modules, refer to their respective Instructions for Use or Operator's Manuals. 

 

Troubleshooting Root 

Symptom 

Possible Cause   

Correction 

Root does not turn on. 

Power Button not 

pressed long 

enough. 

Press Power Button for two (2) seconds. 

The battery may be 

depleted. 

Connect Root to AC power to charge battery. 

One of the fuses is 

not operating 

properly. 

Replace the fuse. See 

Replacing the Fuses

 on 

page 135. 

Root turns on, but 

Main Screen is dim or 

blank. 

The brightness 

setting is not 

correct. 

Adjust the brightness setting. See 

Brightness

 

on page 48.   
If the condition persists, Root requires service. 

Contact Masimo Technical Support. See 

Return Procedure

 on page 140. 

Touch functionality is 

not responsive. 

Internal failure. 

Root requires service. Contact Masimo 

Technical Support. See 

Return Procedure

 on 

page 140. 

Not displaying data 

from Radical-7, 

Radius-7, or MOC-9 

modules. 

Connection error. 

Ensure that the connections are securely in 

place and properly plugged in, or that the 

cable is not defective. For Radius-7, ensure 

that the device is paired with Root via 

Bluetooth. Refer to Operator's Manual of 

Radius-7 for more information. 

Iris screen does not 

display connection 

status for standalone 

devices. 

Connection error. 

Unplug and replug the Iris Adapter. 

Summary of Contents for Root

























































































































































Reviews:

No comments