manualshive.com logo in svg

Masimo Root, Operator'S Manual, Page: 73 / 152

Share
Download
Masimo Root Operator'S Manual Download Page 73

Root   

Chapter 3: Operation 

 

www.masimo.com 

71 

  Masimo   

 

 

Audio Pause 

Audio Pause temporarily suspends all audible alarms on Root. When it is active, visual alarms 

are not impacted and will still display. The Audio Pause icon is located on the left side of the 

Status Bar – do not confuse with the Sounds icon on the right side of the Status Bar. See 

About the Status Bar

 on page 29. 

By default, Audio Pause is inactive, and the icon appears in the following way: 

 

Audio Pause inactive

 

 

To activate Audio Pause, press the icon. It will turn red and the remaining Audio Pause 

Duration time counts down next to the icon. The default duration for Audio Pause is 120 

seconds. In the example below, Audio Pause is activated, and there are 15 seconds left until 

Audio Pause is inactive again. 
To configure Audio Pause, see 

Sounds

 on page 56.   

 

Audio Pause active. 15 seconds until Audio Pause is inactive.

 

 

Note:

 When Audio Pause is activated, powering off and then powering on Root will return 

Audio Pause to its default inactive state. 

 

Summary of Contents for Root

























































































































































Reviews:

No comments