Page 15
5.20 Program Function Relay 2 / K26 Relay (RX)
1) Press “
→
” button to enter Function Relay 2 setting.
2) Press “
↑
” and “
↓
” button to scroll and select.
3) Exit Program Function Relay 2 by pressing the “BACK” button until the
cursor is shown next to “FUNC RLY2”.
4) Press “
↑
” and “
↓
” button to scroll through other Flex EX2 settings.
--- : START
function
only.
LV
:
Function relay closes when receiver voltage is low.
ID
:
Function relay works simultaneously with all motion commands.
NORMAL
:
START fu AUX with normal momentary output.
TOGGLE
:
START fu AUX with toggled/latching output.
TOG&E
:
START fu AUX with toggled/latching output. The relay opens when
STOP button is pressed down and transmitter power off.
S/P
:
FUNCTION relay closes when START command is executed and opens only when
transmitter power is turned off.
EXT
:
FUNCTION relay works simultaneously with the receiver MAIN relays.
TDM A+B
:
FUNCTION relay closes when selector switch is rotated to the A+B position
and opens when rotate to A or B positions (tandem monitoring output).
HORN
:
FUNCTION relay closes for up to 3 seconds when START command is initiated
at transmitter power on and then becomes normal momentary outputs thereafter.
G SENSOR
:
FUNCTION relay closes when Zero-G sensor is triggered (receiver MAIN
relays deactivated) and opens when receiver MAIN relays are reactivated.
RS
:
For RS system, the function relay works simultaneously with the Select pushbutton.
5.21 Program Function Relay 3 / K30 Relay (RX)
1) Press “
→
” button to enter Function Relay 3 setting.
2) Press “
↑
” and “
↓
” button to scroll and select.
3) Exit Program Function Relay 3 by pressing the “BACK” button until the
cursor is shown next to “FUNC RLY3”.
4) Press “
↑
” and “
↓
” button to scroll through other Flex EX2 settings.
--- : START
function
only.
LV
:
Function relay closes when receiver voltage is low.
ID
:
Function relay works simultaneously with all motion commands.
NORMAL
:
START fu AUX with normal momentary output.
TOGGLE
:
START fu AUX with toggled/latching output.
TOG&E
:
START fu AUX with toggled/latching output. The relay opens when
STOP button is pressed down and transmitter power off.
S/P
:
FUNCTION relay closes when START command is executed and opens only when
transmitter power is turned off.
EXT
:
FUNCTION relay works simultaneously with the receiver MAIN relays.
TDM A+B
:
FUNCTION relay closes when selector switch is rotated to the A+B position
and opens when rotate to A or B positions (tandem monitoring output).
HORN
:
FUNCTION relay closes for up to 3 seconds when START command is initiated
at transmitter power on and then becomes normal momentary outputs thereafter.
G SENSOR
:
FUNCTION relay closes when Zero-G sensor is triggered (receiver MAIN
relays deactivated) and opens when receiver MAIN relays are reactivated.
RS
:
For RS system, the function relay works simultaneously with the Select pushbutton.
Summary of Contents for FLEX EX
