![background image](http://html1.mh-extra.com/html/magnetek/flex-ex/flex-ex_instruction-manual_3604703072.webp)
Page 71
9.37 Program PB7 Outputs (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB7 Output setting.
3) Press “
→
” button again then “
↑
” and “
↓
” button to scroll and select “Digital”,
“Current”, Voltage or “PWM”.
4) Press “BACK” button and then “
↑
” and “
↓
” button to select values for “Current”,
“Voltage”, and “PWM” settings.
5) Press “
→
” button to enter setting and “
↑
” and “
↓
” button to select numeric
value for the digit to the far left. Press “
→
” button to go to the next digit and
press
“
↑
” and “
↓
” button to select.
6) Press “BACK” button to go back to step 5.
7) Exit Program PB7 Output by pressing the “BACK” button until the cursor is
shown next to “PB7 OUT”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
9.38 Program PB8 Outputs (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB8 Output setting.
3) Press “
→
” button again then “
↑
” and “
↓
” button to scroll and select “Digital”,
“Current”, Voltage or “PWM”.
4) Press “BACK” button and then “
↑
” and “
↓
” button to select values for “Current”,
“Voltage”, and “PWM” settings.
5) Press “
→
” button to enter setting and “
↑
” and “
↓
” button to select numeric
value for the digit to the far left. Press “
→
” button to go to the next digit and
press
“
↑
” and “
↓
” button to select.
6) Press “BACK” button to go back to step 5.
7) Exit Program PB8 Output by pressing the “BACK” button until the cursor is
shown next to “PB8 OUT”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
9.39 Program PB9 Outputs (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB9 Output setting.
3) Press “
→
” button again then “
↑
” and “
↓
” button to scroll and select “Digital”,
“Current”, Voltage or “PWM”.
4) Press “BACK” button and then “
↑
” and “
↓
” button to select values for “Current”,
“Voltage”, and “PWM” settings.
5) Press “
→
” button to enter setting and “
↑
” and “
↓
” button to select numeric
value for the digit to the far left. Press “
→
” button to go to the next digit and
press
“
↑
” and “
↓
” button to select.
6) Press “BACK” button to go back to step 5.
7) Exit Program PB9 Output by pressing the “BACK” button until the cursor is
shown next to “PB9 OUT”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
Summary of Contents for FLEX EX
