Page 70
9.34 Program PB4 Outputs (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB4 Output setting.
3) Press “
→
” button again then “
↑
” and “
↓
” button to scroll and select “Digital”,
“Current”, Voltage or “PWM”.
4) Press “BACK” button and then “
↑
” and “
↓
” button to select values for “Current”,
“Voltage”, and “PWM” settings.
5) Press “
→
” button to enter setting and “
↑
” and “
↓
” button to select numeric
value for the digit to the far left. Press “
→
” button to go to the next digit and
press
“
↑
” and “
↓
” button to select.
6) Press “BACK” button to go back to step 5.
7) Exit Program PB4 Output by pressing the “BACK” button until the cursor is
shown next to “PB4 OUT”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
9.35 Program PB5 Outputs (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB5 Output setting.
3) Press “
→
” button again then “
↑
” and “
↓
” button to scroll and select “Digital”,
“Current”, Voltage or “PWM”.
4) Press “BACK” button and then “
↑
” and “
↓
” button to select values for “Current”,
“Voltage”, and “PWM” settings.
5) Press “
→
” button to enter setting and “
↑
” and “
↓
” button to select numeric
value for the digit to the far left. Press “
→
” button to go to the next digit and
press
“
↑
” and “
↓
” button to select.
6) Press “BACK” button to go back to step 5.
7) Exit Program PB5 Output by pressing the “BACK” button until the cursor is
shown next to “PB5 OUT”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
9.36 Program PB6 Outputs (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB6 Output setting.
3) Press “
→
” button again then “
↑
” and “
↓
” button to scroll and select “Digital”,
“Current”, Voltage or “PWM”.
4) Press “BACK” button and then “
↑
” and “
↓
” button to select values for “Current”,
“Voltage”, and “PWM” settings.
5) Press “
→
” button to enter setting and “
↑
” and “
↓
” button to select numeric
value for the digit to the far left. Press “
→
” button to go to the next digit and
press
“
↑
” and “
↓
” button to select.
6) Press “BACK” button to go back to step 5.
7) Exit Program PB6 Output by pressing the “BACK” button until the cursor is
shown next to “PB6 OUT”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
Summary of Contents for FLEX EX
