Page 72
9.40 Program PB10 Outputs (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB10 Output setting.
3) Press “
→
” button again then “
↑
” and “
↓
” button to scroll and select “Digital”,
“Current”, Voltage or “PWM”.
4) Press “BACK” button and then “
↑
” and “
↓
” button to select values for “Current”,
“Voltage”, and “PWM” settings.
5) Press “
→
” button to enter setting and “
↑
” and “
↓
” button to select numeric
value for the digit to the far left. Press “
→
” button to go to the next digit and
press
“
↑
” and “
↓
” button to select.
6) Press “BACK” button to go back to step 5.
7) Exit Program PB10 Output by pressing the “BACK” button until the cursor
is shown next to “PB10 OUT”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
9.41 Program PB11 Outputs (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB11 Output setting.
3) Press “
→
” button again then “
↑
” and “
↓
” button to scroll and select “Digital”,
“Current”, Voltage or “PWM”.
4) Press “BACK” button and then “
↑
” and “
↓
” button to select values for “Current”,
“Voltage”, and “PWM” settings.
5) Press “
→
” button to enter setting and “
↑
” and “
↓
” button to select numeric
value for the digit to the far left. Press “
→
” button to go to the next digit and
press
“
↑
” and “
↓
” button to select.
6) Press “BACK” button to go back to step 5.
7) Exit Program PB11 Output by pressing the “BACK” button until the cursor
is shown next to “PB11 OUT”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
9.42 Program PB12 Outputs (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB12 Output setting.
3) Press “
→
” button again then “
↑
” and “
↓
” button to scroll and select “Digital”,
“Current”, Voltage or “PWM”.
4) Press “BACK” button and then “
↑
” and “
↓
” button to select values for “Current”,
“Voltage”, and “PWM” settings.
5) Press “
→
” button to enter setting and “
↑
” and “
↓
” button to select numeric
value for the digit to the far left. Press “
→
” button to go to the next digit and
press
“
↑
” and “
↓
” button to select.
6) Press “BACK” button to go back to step 5.
7) Exit Program PB12 Output by pressing the “BACK” button until the cursor
is shown next to “PB12 OUT”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
Summary of Contents for FLEX EX
