Leviton MLC16 User Manual Download Page 12

Page: 12 / 70

User Guide

Page 6 of 62

Leviton MLC 16D Motorized Lighting Controller

•

Aud:

To adjust the audio gain, turn Modify wheel 3. Use this to fine-tune the

console's response from a line level audio signal input active in the Audio mode.

•

GM:

To raise or lower the console's Grand Master level, turn Modify wheel 4.

This only controls traits that are assigned to the Grand Master in the fixture's

definition. Typically this is used as a master control for all fixture dimmer traits.

All procedures in this User Guide begin at the MLC 16D Main Screen. You

can return to the MLC 16D Main Screen from any of the Record or Edit

menus by pressing

Edit

Blackout

Installation and Setup

Power Supply

The MLC 16D requires 120 VAC to operate. To turn the console on:

Connect the AC power cable (supplied) to a source of AC power.

Press the power switch located next to the power input connector.

DMX512 Input and Output

Leviton ships the MLC 16D console with two DMX512 output connectors and one

DMX512 input connector. One output connector is a standard USITT specified

5-pin female XLR. The other is a 3-pin female XLR connector used by some fixture

manufacturers. The input connector is a standard USITT specified 5-pin male XLR.

Be sure the fixture connector pin-out matches that of the MLC 16D. For

example, Martin fixtures use a 3-pin XLR, but reverses pin 2 and 3 from

the norm. Pins 2 and 3 of the 3-pin XLR can be swapped internally to

support these situations. See the chapter "3-Pin XLR Pin Reversal" for

details.

The DMX512 digital signal provides the highest speed, precision, and noise

immunity. When connecting DMX512:

•

Use cable that is specified as RS-485 or RS-422 compatible (shielded, 1 or 2

twisted pair) and use the largest gauge available (22-18 gauge is good for long

runs of 1000 ft).

•

Daisy chain the cable only (no star or home runs) and terminate the end of the

cable with a 120-ohm resistor. (See the fixture's manual for proper terminating

practices).

Using Audio Input

You can use a line level audio signal from an audio source such as a CD player or

mixer to trigger steps in patterns and shows based on the beat of the audio

source. When a line source is present (connected with a standard ¼-in. RCA jack)

and the

Audio

button LED is on, Audio mode is active and will override hold times

programmed in patterns. You can control the audio gain using the Modify wheel 3

and the LCD display. A higher value increases the gain.

Summary of Contents for MLC16







































































Search results

Summary of Contents for MLC16

Reviews:

Related manuals for MLC16

Brands by name

Popular brands

Leviton MLC16, User Manual

Search results

Summary of Contents for MLC16

Reviews:

Related manuals for MLC16

Brands by name

Popular brands