Labconco Logic+ A2 Technical Manual Download Page 159

Page: 159 / 201

159

Airflow Sensor (optional)

1. From the Home Screen, press

[MENU]

2. Press

[UP]

to select the

Tools

option.

3. Press

[OK/MUTE]

to enter the submenu.

4. Press

[DOWN]

until the

Diagnostics

option is

highlighted, then

[OK/MUTE]

to enter the

submenu.

5. Press

[DOWN]

until the

Airflow Sensor

option is

highlighted, then

[OK/MUTE]

to enter Airflow

Sensor diagnostics.

6. The display shows the status of the airflow

sensor in the following order:



current sensor output in millivolts,



current inflow, corrected for the display



zero set-point in millivolts



alarm set-point in millivolts



nominal (105 FPM or 0.53 m/s) output in

millivolts.

7. Press

[MENU]

to return to the Diagnostic submenu.

Summary of Contents for Logic+ A2










































































































































































































Search results

Summary of Contents for Logic+ A2

Reviews:

Related manuals for Logic+ A2

Brands by name

Popular brands

Labconco Logic+ A2, Technical Manual

Search results

Summary of Contents for Logic+ A2

Reviews:

Related manuals for Logic+ A2

Brands by name

Popular brands