Labconco Logic+ A2 Technical Manual Download Page 157

Page: 157 / 201

157

15: Diagnostics

This section details diagnostic functions available through the software of the biosafety
cabinet.

Sash Sensors

1. From the Home Screen, press

[MENU]

2. Press

[UP]

to select the

Tools

option.

3. Press

[OK/MUTE]

to enter the submenu.

4. Press

[DOWN]

until the

Diagnostics

option is

highlighted, then

[OK/MUTE]

to enter the submenu.

5. The

Sash Sensors

option is the first option, press

[OK/MUTE]

to enter Sash Sensor diagnostics.

Note:

If the blower is on when entering the Sash

Sensor Diagnostic screen, it will automatically

turn off.

6. Slowly raise the sash from fully closed to open. When

closed, the screen will report

CLOSED

. Below or

above the proper sash height, the screen will report

NOT AT WORKING HEIGHT

. At the proper sash

height (+/- 0.75 inches), the screen will report

WORKING HEIGHT

. Type A2 12-inch and C1 will also

report

ALMOST CLOSED

when sash 2-3 inches (5-8

cm) above closed.

7. Press

[MENU]

to return to the Diagnostic submenu.

Summary of Contents for Logic+ A2










































































































































































































Search results

Summary of Contents for Logic+ A2

Reviews:

Related manuals for Logic+ A2

Brands by name

Popular brands

Labconco Logic+ A2, Technical Manual

Search results

Summary of Contents for Logic+ A2

Reviews:

Related manuals for Logic+ A2

Brands by name

Popular brands