KYMCO MXU 500 Owner'S Manual Download

Page: 603 / 664

. BATTERY/CHARGING SYSTEM

17-4

MXU 500

TROUBLESHOOTING

Battery is damaged or weak

Faulty battery

Faulty regulator/rectifier.

Shorted wire harness.

Faulty ignition switch.

Faulty charging coil.

Faulty battery.

Open circuit in related wire.

Loose or poor contacts of related

terminal.

Shorted wire harness

Faulty regulator/rectifier

Correct

Remove the battery.

Check the battery condition.

Install the battery.

Check the battery current leakage.

Specified current leakage: 0.5 Ma
max

Check the alternator charging coil.

Standard:

0.1 – 0.3

(20°C/68°F)

Measure and record the battery

voltage using a digital multimeter.

Start the engine.

Measure the charging voltage.

Compare the measurements to result

of the following calculation.

Measured voltage < measured
charging voltage < 15.5 V

Perform the regulator/rectifier wire

harness inspection.

Correct

Disconnect the regulator/rectifier

connectors and recheck the battery

current leakage.

Incorrect

Correct

Incorrect

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MXU 500

Reviews:

Related manuals for MXU 500

Brands by name

Popular brands

KYMCO MXU 500, Owner'S Manual

Search results

Summary of Contents for MXU 500

Reviews:

Related manuals for MXU 500

Brands by name

Popular brands