KYMCO MXU 500 Owner'S Manual Download Page 150

Page: 150 / 664

Troubleshooting chart

Use electric starter
to see if there is
compression.

There is compression.

Compression normal.

No compression.

Ask a KYMCO dealer to inspect.

2. Battery

Use electric
starter.

Engine turns
over quickly.

Battery good.

Check fluid, recharge, check connections.

Engine turns
over slowly.

Water or dirt
mixed in fuel.

Turn the fuel
valve to

Clean filter element
and fuel tank.

Check fuel flow.

No fuel.

Fuel valve

Clean fuel valve.

Turn the fuel
valve to "OFF".

Turn the fuel
valve to "RES".

Supply fuel.

1. Fuel

Remove the fuel
hose from the
fuel valve.

Check if there is
fuel in the fuel
tank.

There is fuel.

Some fuel.

No fuel.

Restart engine.

Ask a KYMCO dealer to inspect.

Adjust plug gap or
replace plug.

Spark weak.

No spark.

Spark good.

Ignition system normal.

4. Compression

3. Ignition

Remove plug and
check electrode.

Wipe clean with dry
cloth.

Attach plug cap and
ground to chassis.

Use electric
starter.

Wet

Dry

140

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MXU 500

Reviews:

KYMCO MXU 500, Owner'S Manual, Page: 150 / 664

Search results

Summary of Contents for MXU 500

Reviews: