manualshive.com logo in svg

KYMCO MXU 500, Owner'S Manual, Page: 225 / 664

Share
Download
KYMCO MXU 500 Owner'S Manual Download Page 225

2

. FRAME COVERS/EXHAUST MUFFLER

 

2-14

 MXU 500

Remove the exhaust pipe and gasket.

INSTALLATION

Replace the gaskets with new ones.
Install the exhaust pipe and tighten the joint
nuts.

Torque:
Exhaust pipe mounting nut:

3.5 kgf-m (35 N-m, 14 lbf-ft)

Install the muffler and tighten the mounting
bolts

Torque:
Exhaust muffler mounting bolt:

3.5 kgf-m (35 N-m, 14 lbf-ft)

Install and tighten the band bolts.

Torque:

 2.1 kgf-m (21 N-m, 15 lbf-ft)

            Gasket

    Exhaust Pipe

Be sure to install a new exhaust gasket.

＊

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments