KYMCO MXU 500 Owner'S Manual Download Page 587

Page: 587 / 664

. BRAKE SYSTEM

16-35

MXU 500

REAR BRAKE CALIPERS

REMOVAL/INSTALLATION

Drain the brake fluid from the hydraulic

brake system (refer to the “

REAR BRAKE

FLUID CHANGE/AIR BLEED

” section

in this chapter).

Remove the brake fluid hose bolt and two

washers from the caliper.

Remove the brake pads (refer to the

“

BRAKE PADS REPLACEMENT

”

section in this chapter).

Remove the brake caliper.

INSTALLATION

Install the brake fluid hose with the

attaching bolt and two new sealing washers,

then tighten the bolt to the specified torque.

Torque: 3.5 kgf-m (35 Nm, 25 lbf-ft)

Fill the specified brake fluid and bleed air

from the brake system (refer to the “

REAR

BRAKE FLUID CHANGE/AIR BLEED

”

section in this chapter).

Caliper (Brake Lever)

OFF ROAD Type: Caliper (Brake Pedal)

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MXU 500

Reviews:

KYMCO MXU 500, Owner'S Manual, Page: 587 / 664

Search results

Summary of Contents for MXU 500

Reviews: