KYMCO MXU 500 Page 232 Owner'S Manual Download

Page: 232 / 664

. INSPECTION/ADJUSTMENT

3-6

MXU 500

3. Loosen the screw (3) and remove the air

cleaner assembly (4) from the air cleaner
housing.

4. Unscrew the clamp (5)

5. Remove the outer air cleaner (7).
6. Remove the screw/washers (6) and

remove the air cleaner assembly from the
air cleaner holder (8).

7. Remove the inner air cleaner (9) and air

cleaner screen (10) from the air cleaner
guide (11).

8. Remove the air cleaner screen from the

inner air cleaner.

CLEAN AIR FILTER ELEMENT

Wash the element gently, but throughly in
solvent.

Squeeze the excess solvent out of the
element and let dry.

Apply the engine oil.
Squeeze out the excess oil.

More frequent replacement is required when
riding in unusually dusty or rainy areas.

(7)

(8)

(9)

(10)

(11)

Use parts cleaning solvent only. Never
use gasoline or low flash point solvents
which may lead to a fire or explosion.

＊

Do not twist or wring out the foam
element. This could damage the foam
material.

＊

The element should be wet but not
dripping.

＊

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MXU 500

Reviews:

Related manuals for MXU 500

Brands by name

Popular brands

KYMCO MXU 500, Owner'S Manual

Search results

Summary of Contents for MXU 500

Reviews:

Related manuals for MXU 500

Brands by name

Popular brands