manualshive.com logo in svg

KYMCO MXU 500, Owner'S Manual

The KYMCO MXU 500 Owner's Manual is available for free download on our website. This comprehensive manual provides detailed instructions on the proper maintenance and operation of your MXU 500, ensuring a smooth and safe riding experience. Download it now from manualshive.com and get ready to hit the trails!

Share
Download
background image

8. CYLINDER HEAD/VALVES

8-15

  MXU 500

ROCKER ARMS

REMOVAL/INSPECTION/

INSTALLATION

REMOVAL

Remove the camshafts (refer to the

“

CAMSHAFT REMOVAL/INSPECTION/

INSTALLATION

” section in this chapter).

Remove the rocker arm shafts and washers,

then remove the rocker arms.

INSPECTION

Rocker arm shaft

Inspect the rocker arm shaft for blue

discoloration or grooves.
If any defects are found, replace the rocker

arm shaft with a new one, then inspect

lubrication system.

Measure each rocker arm shaft O.D.
Measure the I.D. of each rocker arm.
Measure arm to shaft clearance.
Replace as a set if out of specification.

Service limits: 

0.1 mm (0.004 in)

Inspect the rocker arm bore, cam lobe contact

surface and adjuster surface for

wear/pitting/scratches/blue discoloration.
If any defects are found, replace the rocker
arm shaft with a new one, then inspect
lubrication system.

Measure each rocker arm shaft O.D.
Measure the I.D. of each rocker arm.
Measure arm to shaft clearance.
Replace as a set if out of specification.

Service limits: 

0.1 mm (0.004 in)

                             

Rocker Arm Shaft

                            Rocker Arm Shafts/Washers

Rocker Arms

                                          Rock Arm

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MXU 500

Honda 1997 Fourtrax TRX250 Owner'S Manual preview
1997 Fourtrax TRX250
Brand: Honda Pages: 155
Club Car 1989 DS Owner'S Manual preview
1989 DS
Brand: Club Car Pages: 20
Snapper GC9520KWV Setup Manual preview
GC9520KWV
Brand: Snapper Pages: 6
Snapper 63337 Parts Manual preview
63337
Brand: Snapper Pages: 8
Snapper 7085632 Safety Instructions & Operator'S Manual preview
7085632
Brand: Snapper Pages: 36
Applestone APU06E Owner'S Manual preview
APU06E
Brand: Applestone Pages: 134
Egholm ST800 Operator'S Manual preview
ST800
Brand: Egholm Pages: 16
Erde 213 Assembly And Usage Instructions preview
213
Brand: Erde Pages: 4
Meec tools 707-054 Operating Instructions Manual preview
707-054
Brand: Meec tools Pages: 56
Ventrac KW450 Operator'S Manual & Parts Drawings preview
KW450
Brand: Ventrac Pages: 83
Dane Technologies QuicKART 2000 Series Service Manual preview
QuicKART 2000 Series
Brand: Dane Technologies Pages: 115
PACIFIC RIM INT’L WEST PAZ200-1 Owner'S Manual preview
PAZ200-1
Brand: PACIFIC RIM INT’L WEST Pages: 21
Toro UTV 700 EFI Pre-Delivery Setup Instructions preview
UTV 700 EFI
Brand: Toro Pages: 12
Verhagen Leiden V-move 650 User Manual preview
V-move 650
Brand: Verhagen Leiden Pages: 17
URBANGLIDE Quad 4.0 User Manual preview
Quad 4.0
Brand: URBANGLIDE Pages: 98
Textron ALTERRA MUD PRO 700 LTD EPS 2018 Operator'S Manual preview
ALTERRA MUD PRO 700 LTD EPS 2018
Brand: Textron Pages: 76
Montracon MT45 Operator'S Handbook Manual preview
MT45
Brand: Montracon Pages: 74
Ezgo EZGO 2001 Owner'S Manual And Service Manual preview
EZGO 2001
Brand: Ezgo Pages: 50

Brands by name

Popular brands

Load more brands