manualshive.com logo in svg

KYMCO MXU 500, Owner'S Manual, Page: 287 / 664

Share
Download
KYMCO MXU 500 Owner'S Manual Download Page 287

5

. FUEL SYSTEM

 

5-9

          MXU 500

CARBURETOR
DISASSEMBLY/INSPECTION/
ASSEMBLY

DISASSEMBLY

Remove the carburetor (refer to the

“

CARBURETOR REMOVAL/CHOKE

INSPECTION/INSTALLATION

” section in

this chapter).

Loosen the drain screw to drain the gasoline

from the float chamber.

Remove the four screws and top cap

.

Remove the spring and piston valve.

Fuel Drain Plug

Spring

Top Cap

Piston Valve

x

Keep sparks and flames away from the

work area.

x

Drain gasoline into a clean container.

x

 Do not loosen or tighten the painted

bolts and screws of the carburetor.

Loosening or tightening them can

cause throttle and piston valve

synchronization failure.

＊

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments