manualshive.com logo in svg

KYMCO MXU 500, Owner'S Manual, Page: 249 / 664

Share
Download
KYMCO MXU 500 Owner'S Manual Download Page 249

3

. INSPECTION/ADJUSTMENT

     

3-23

      MXU 500

STEERING SYSTEM
INSPECTION

Place the machine on a level place.
Check the steering column bushings and
bearings:
Move the handlebar up and down, and/or
back and forth.
Replace the steering column bushings and
or bearings if excessive play

Check the tie-rod ends
Turn the handlebar to the left and/or right
until it stops completely, then slightly move
the handlebar from left to right.
Replace the tie-rod ends if tie-rod end has
any vertical play.

Raise the front end of the machine so that
there is no weight on the front wheels.
Check ball joints and/or wheel bearings.
Move the wheels lately back and froth.
Replace the front arms and/or wheel
bearings if excessive free play.

Tie-rod Ends

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments