KYMCO MXU 500 Owner'S Manual Download Page 396

Page: 396 / 664

10. DRIVE PULLEY/DRIVEN PULLEY/CLUTCH

10-26

MXU 500

Apply lightweight lithium-soap base grease

to the new oil seal lip, then install the new

oil seal.

Install the clutch housing.

One-way clutch bearing installation:

Install the one-way clutch bearing into the

clutch housing.

Oil Seal

Clutch Housing

The one-way clutch bearing should be

installed in the clutch carrier assembly

with the arrow mark and “OUT SIDE”

mark facing toward the clutch carrier

assembly.

＊

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MXU 500

Reviews:

KYMCO MXU 500, Owner'S Manual, Page: 396 / 664

Search results

Summary of Contents for MXU 500

Reviews: