KYMCO MXU 500 Owner'S Manual Download Page 650

Page: 650 / 664

20. LIGHTS/SWITCHES

20-5

MXU 500

IGNITION SWITCH

INSPECTION

Disconnect the ignition switch connectors.

(Refer to the “

FRAME COVER

” section in

the chapter 2.)

Check for continuity between the switch

side connector terminals in each switch

position.
Continuity should exist between the color

coded wires as right:

REPLACEMENT

Release the switch wire from the wire clips

on the steering shaft holder frame pipe.

Remove the meter cover (refer to the

“

FRAME COVER

” section in the chapter

2).
Remove the ignition switch from the cover

while pushing in the two stoppers.

Install a new ignition switch by aligning the

locating tab with the groove in the cover.

Install the removed parts in the reverse

order of removal.

HANDLEBAR SWITCH

INSPECTION

Remove front center cover (refer to the

“

FRAME COVER

” section in the chapter

2).
Disconnect the connectors.

Check for continuity between the switch

side connector terminals in each switch

position.
Continuity should exist between the color

coded wires as next page:

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MXU 500

Reviews:

KYMCO MXU 500, Owner'S Manual, Page: 650 / 664

Search results

Summary of Contents for MXU 500

Reviews: