KYMCO Mongoose 50-2T Service Manual Download Page 45

Page: 45 / 258

. FRAME COVERS/EXHAUST MUFFLER

2-8

Inspect the gasket.
If the exhaust gas leaks, the gasket should
be replaced.

Install by reversing the removal sequence.

Torque:

Exhaust muffler lock bolt

35 N-m (3.5 kgf-m, 25 lbf-ft)

Exhaust muffler lock nut (90cc/70cc/50cc-

2T)

20 N-m (2 kgf-m, 15 lbf-ft)

Exhaust muffler lock nut (50cc-4T)

10 N-m (1 kgf-m, 7 lbf-ft)

TAILLIGHT BULB

REMOVAL

Remove the two screws and taillight lens.

Turn bulb and remove it.

Be sure to install a new exhaust gasket.

＊

Gasket

Screws

Bulb

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands