KYMCO Mongoose 50-2T Service Manual Download Page 253

Page: 253 / 258

. STARTING SYSTEM

16-10

STARTER PINION (70cc/50cc-

4T/50cc-2T)

REMOVAL

Remove the left crankcase cover.

Remove the drive pulley.
(Refer to chapter 9)

Remove the starter pinion cover (50cc-2T

only).
Remove the starter pinion.

INSPECTION

Inspect the starter pinion seat for wear.

Inspect the starter pinion for smooth

operation.

Inspect the starter pinion shaft forcing parts

for wear and damage.

INSTALLATION

Apply a small amount of grease to the

starter pinion teeth.

Install the starter pinion in the reverse order

of removal.

Starter Pinion

Shaft Forcing Parts

Starter Pinion

Starter Pinion Cover (50cc-2T only)

50cc-2T

Starter Pinion

70cc/50cc-4T

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands