KYMCO Mongoose 50-2T Service Manual Download Page 133

Page: 133 / 258

. CYLINDER/PISTON

8-9

PISTON RING INSTALLATION

Install the piston rings onto the piston.

Apply engine oil to each piston ring.

Measure the connecting rod small end I.D.

Service Limit

: 13.06 mm (0.5224 in)

Measure the connecting rod to piston pin

clearance.

Service Limit

: 0.06 mm (0.0024 in)

Inspect the exhaust side and intake side

chain guides.
Wear/Damage

→

Replace.

Second

Side Rail

Top

Side Rail

Oil Ring

•

Be careful not to damage or break the

piston and piston rings.

•

All rings should be installed with the

markings facing up.

•

After installing the rings, they should

rotate freely without sticking.

＊

Intake Side Guide

Exhaust Side Guide

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands