KYMCO Mongoose 50-2T Service Manual Download Page 208

Page: 208 / 258

. REAR WHEEL/SWING ARM/

HYDRAULIC BRAKE

13-10

REAR SWING ARM

REMOVAL

Place the machine on a level place.
Elevate the rear wheels by placing a suitable
stand under the rear of frame.

Remove the rear wheels, rear hubs, rear axle
and axle hub. (Refer to the “REAR
WHEEL” section in chapter 13.)

Remove the lower bolt attaching the rear
shock absorber.

Remove the upper bolt and then remove the
shock absorber.

INSPECTION

Check the tightening torque of the pivot
shaft (swing arm) securing nut.

Torque:

70 N-m (7 kgf-m, 50 lbf-ft)

Lower Bolt

Support the machine securely so there is
no danger of it falling over.

＊

When removing the lower bolt, hold the
swing arm so that it does not drop
downwards when the bolt is removed.

＊

Upper Bolt

Securing Nut

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands