KYMCO Mongoose 50-2T Service Manual Download Page 134

Page: 134 / 258

. CYLINDER/PISTON

8-10

PISTON INSTALLATION

Remove any gasket material from the

crankcase surface.

Install the piston, piston pin and a new

piston pin clip.

CYLINDER INSTALLATION

Install the dowel pins and a new cylinder

gasket on the crankcase.
Coat the cylinder bore, piston and piston

rings with clean engine oil.

Carefully lower the cylinder over the piston

by compressing the piston rings.

•

Apply proper clean engine oil around

cylinder wall.

•

Be careful not to damage or break the

piston rings.

•

Stagger the ring end gaps at 120

to the

piston pin.

＊

Be careful not to drop foreign matters

into the crankcase.

＊

•

Position the piston “IN” mark on the

intake valve side.

•

Place a clean shop towel in the

crankcase to keep the piston pin clip

from falling into the crankcase.

＊

“IN” Mark

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands