KYMCO Mongoose 50-2T Service Manual Download Page 100

Page: 100 / 258

. FUEL SYSTEM

5-13

CAUTIONS!

ASSEMBLY

Reverse the “DISASSEMBLY” procedures.

•

Be careful not to damage the jets and
jet holder when removing them.

•

Before removal, turn the throttle stop
screw and air screw in and count the
number of turns until they seat lightly
and then make a note of this.

•

Do not force the screw against its seat
to avoid seat damage.

•

Be sure to install the O-ring in the
reverse order of removal.

＊

Needle Jet

Throttle Stop Screw

Spring

Air Screw

Spring

Washer

O-ring

Main Jet

Needle Jet Holder

Slow Jet

•

When installing the air screw, return it
to the original position as noted during
removal

•

Refer to the “CARBURETOR IDLE
SPEED” section in chapters to perform
the idle speed adjustment.

•

After the carburetor is installed, be
sure to perform the Exhaust Emission
T t

＊

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands