KYMCO Mongoose 50-2T Service Manual Download Page 170

Page: 170 / 258

.CRANKSCASE/CRANKSHAFT

11-4

CRANKCASE/CRANKSHAFT
(90cc/70cc/50cc-4T)

REMOVAL

Remove the crankcase attaching bolt.
Separate the left and right crankcase halves.

Remove the crankshaft from the left
crankcase.

Remove the cam chain.
Remove the gasket and dowel pins.

Clean off all gasket material from the
crankcase mating surfaces.

Bolt

Crankshaft

•

Do not damage the crankcase gasket
surface.

•

Never use a driver to pry the crankcase
mating surfaces apart.

＊

Cam Chain

Dowel Pins

Gasket

Avoid damaging the crankcase mating
surfaces.

＊

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands