KYMCO Mongoose 50-2T Service Manual Download Page 91

Page: 91 / 258

. FUEL SYSTEM

5-4

FUEL TANK

REMOVAL

Remove front fender (See page 2-5).

Switch the fuel valve “OFF”.
Disconnect the fuel outlet tube from fuel
valve.
Remove two screws attaching the fuel valve
and holder.

Remove the two bolts and then remove the
fuel tank.

INSTALLATION

Reverse the “FUEL TANK REMOVAL”
procedures.

FUEL VALVE

REMOVAL

Remove the screw and then remove control
switch.
Disconnect all fuel tubes and then remove
fuel valve.

Warning

Fuel Tank

Screw

Fuel Valve

Bolts

Fuel Outlet Tube

•

Keep sparks and flames away from the
work area.

•

Wipe off any spilled gasoline.

Control Switch

Fuel Tubes

Screws

•

Keep sparks and flames away from the
work area.

•

Drain gasoline into a clean container.

＊

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands