KYMCO Mongoose 50-2T Service Manual Download Page 123

Page: 123 / 258

7. CYLINDER HEAD/VALVES

(90cc/70cc/50cc-4T)

7-13

ASSEMBLY

Install the valve spring seats and oil seal.

Lubricate each valve with engine oil and
insert the valves into the valve guides.
Install the valve springs and retainers.

Compress the valve springs using the valve
spring compressor, then install the valve
cotters.

Special tool

Valve Spring Compressor A120E00040

Tap the valve stems gently with a plastic
hammer for 2

～

3 times to firmly seat the

cotters.

INSTALLATION

Install the dowel pins and a new cylinder
head gasket.

Reverse the “CYLINDER HEAD
REMOVAL” procedures.

Torque:

Cylinder head bolt:

10 N-m (1 kgf-m, 7 lbf-ft)

Dowel Pins

Gasket

•

When assembling, a valve spring
compressor must be used.

•

Install the cotters with the pointed ends
facing down from the upper side of the
cylinder head.

＊

Be sure to install new oil seal.

＊

Be careful not to damage the valves.

＊

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands