KYMCO Mongoose 50-2T Service Manual Download Page 164

Page: 164 / 258

.FINAL REDUCTION/

TRANSMISSION SYSTEM

10-5

INSTALLATION

Reverse the “TRANSMISSION REVOVAL”

section procedures.

Install the primary drive axle into the left

crankcase.

Install the final gear and final shaft into left

crankcase.

Install the countershaft and washer into the

left crankcase.
Install the resin washer onto countershaft.

Install the dowel pins and a new gasket onto

the right crankcase.

Install the transmission case cover and tighten

the transmission case cover bolt.

Torque:

27 N-m (2.7 kgf-m, 19 lbf-ft)

Primary Drive Axle

Final Shaft

Countershaft

Resin Washer

Gasket

Dowel Pins

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands