KYMCO Mongoose 50-2T Service Manual Download Page 80

Page: 80 / 258

. LUBRICATION SYSTEM

4-12

Inner Rotor

Screws

Dowel Pin

Measure the rotor end-to-pump body
clearance.

Service Limit:

0.12 mm (0.0048 in)

ASSEMBLY

Install the outer rotor, inner rotor and pump
shaft into the pump body.

Install the dowel pin.
Install the pump cover by aligning the hole
in the cover with the dowel pin.

Tighten the screw to secure the pump cover.
Make sure that the pump shaft rotates freely
without binding.

Insert the pump shaft by aligning the flat
on the shaft with the flat in the inner
rotor.

＊

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands