KYMCO Mongoose 50-2T Service Manual Download Page 184

Page: 184 / 258

. FRONT WHEEL/FRONT BRAKE/FRONT

SUSPENSION/STEERING SYSTEM

12-5

INSPECTION

Measure the wheel run out.
Replace wheel or check bearing play if out
of specification

Rim run out limits

Vertical: 2 mm (0.08 in)

Lateral: 2 mm (0.08 in)

Inspect the front wheel hub.

Replace it if cracks or damage.

Inspect the front brake drum.
Measure the front brake drum I.D.

Service limits

: 84 mm (3.36 in)

Turn the inner race of each bearing with
your finger to see if they turn smoothly and
quietly. Also check if the outer race fits
tightly in the hub.

Replace the bearings if the races do not turn
smoothly, quietly, or if they fit loosely in
the hub.

Keep oil or grease off the brake drum.

＊

Summary of Contents for Mongoose 50-2T



































































































































































































































































Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands

KYMCO Mongoose 50-2T, Service Manual

Search results

Summary of Contents for Mongoose 50-2T

Reviews:

Related manuals for Mongoose 50-2T

Brands by name

Popular brands