Control box
Flowmate Control FMC
47
Screen 28
shows the programme version of the SHC-box and the corresponding date.
W(ater)
Programme version for the liquid system
H(ydraulic)
Programme version for the hydraulic system
Screen 29
shows the programme version of the STC-box (jobcomputer for drawbar - or axle
steering) and the corresponding date. For facilitating the diagnose in case of failure, the electrical
tension (Volt) on the STC-box is also shown.
Screen 33
shows the programme version of the
APC-box (jobcomputer for air fan and oil cooler)
and the corresponding date. For facilitating the diagnose in case of failure, the electrical tension
(Volt) on the
APC-box
is also shown.
§5.24 A
UTOMATIC DRAWBAR
-
OR AXLE STEERING
The both potentiometers (18 and 19) of the
Automatic drawbar - or axle steering
are calibrated in
Screen 30
(fig. 9, 10 or 11).
For good functioning of the Automatic drawbar - or axle steering and the Automatic middle position
of the drawbar/axle, the middle position of both potentiometers (18 and 19) must be calibrated
correctly (fig. 9, 10 or 11).
Mode of procedure in calibration of the potentiometers
- Switch the drawbar - or axle steering in the manual mode by pressing switch
downwards.
- Drive with the tractor carefully straight on and steer the drawbar/axle with the switch
manually till the sprayer follows the tractor in a straight line.
Note:
The drawbar/axle should be now exactly in the middle position and drive in the
imaginary extension of the tractor middle line
- Switch to the entry mode by pressing the
OK-key
. The upper value on screen 30 (= value for
the potentiometer on tractor side) is blinking (fig. 9). The screen displays an additional value
(
"0"
or
"1"
) between the two other values.
- Confirm the displayed value for the front potentiometer with the
OK key.
The next parameter (value
“0”
or
"1"
) is blinking. Don't change this value.
- Confirm the value
"0"
or
"1"
with the
OK-key
; the second value for potentiometer (19) on the
drawbar - or axle steering point (B) is blinking (fig. 10 or 11).
Remark:
The value "0" means that the automatic mode in the software for the drawbar - or
axle steering is activated. When the sprayer is not equipped with
Automatic drawbar
- or axle steering
(the front potentiometer is not mounted (18, fig. 9)), the software
can be deactivated by entering
"1"
.
AUTO
Summary of Contents for Electrical Control EC
