111
Program operating mode
Page 5 - Pitch LFO2
The
“LFO1
Intensity”,
“JS+Y”
and
“AMS”
settings
will
be
added
to
determine
the
depth
and
direction
of
the
pitch
modulation
applied
by
LFO1.
‐
12.00…+12.00
Parameter
value.
PAGE 5 - PITCH LFO2
In
this
page
you
can
set
the
LFO2
modulation
parame
‐
ters
for
the
selected
oscillator.
See
for
information
on
the
various
parameters.
PAGE 6 - PITCH EG
Here
you
can
make
settings
for
the
pitch
EG,
which
cre
‐
ates
time
‐
variant
changes
in
the
pitch
of
the
oscillators.
The
depth
of
pitch
change
produced
by
these
EG
set
‐
tings
on
the
oscillators
is
adjusted
by
the
parameter
(see
Pitch envelope
Start/Attack/Decay/Release Level
These
parameters
specify
the
amount
of
pitch
change.
The
actual
amount
of
pitch
change
will
depend
on
the
parameter
(see
below).
For
example,
with
an
“Intensity”
setting
of
+12.00,
a
“Level”
setting
of
+99
would
raise
the
pitch
one
octave,
and
a
“Level”
setting
of
–99
would
lower
the
pitch
one
octave.
‐
99…+99
Parameter
value.
Start Level
Specifies
the
amount
of
pitch
change
at
note
‐
on.
Attack Level
Specifies
the
amount
of
pitch
change
when
the
attack
time
has
elapsed.
Release Level
Specifies
the
amount
of
pitch
change
when
the
release
time
has
elapsed.
Attack/Decay/Release Time
These
parameters
specify
the
time
over
which
the
pitch
change
will
occur.
0…99
Parameter
value.
Attack Time
Specifies
the
time
over
which
the
pitch
will
change
from
note
‐
on
until
it
reaches
the
pitch
specified
as
the
attack
level.
Decay Time
Specifies
the
time
over
which
the
pitch
will
change
after
reaching
the
attack
level
until
it
reaches
the
nor
‐
mal
pitch.
Release Time
Specifies
the
time
over
which
the
pitch
will
change
from
note
‐
off
until
it
reaches
the
pitch
specified
as
the
release
level.
Pitch EG ‘Level’ modulation
AMS1/2 (L) (Alternate Modulation Source 1/2)
These
parameters
select
the
source
that
will
control
the
pitch
EG
“Level”
parameters
(“AMS
123).
Intensity (AMS1/2 Intensity)
These
parameters
specify
the
depth
and
direction
of
the
effect
applied
by
“AMS1”.
With
a
setting
of
0,
the
levels
specified
by
will
be
used.
For
example
if
“AMS1”
is
Joystick
+Y,
pushing
the
joy
‐
stick
to
turn
it
on
will
change
the
“Level”
parameters
of
the
Pitch
EG.
As
the
absolute
value
of
“Intensity”
is
increased,
the
pitch
EG
levels
will
change
more
greatly
when
the
joystick
is
released.
The
direction
of
the
change
is
specified
by
and
When
the
key
pressure
is
released,
the
pitch
EG
levels
will
return
to
their
own
settings.
If
“AMS1”
is
set
to
Velocity,
increasing
the
absolute
value
of
“Intensity”
will
produce
increasingly
wider
change
in
pitch
EG
levels
for
strongly
‐
played
notes.
The
direction
of
the
change
is
specified
by
and
As
you
play
more
softly,
the
pitch
change
will
draw
closer
to
the
pitch
EG
levels.
‐
99…+99
Parameter
value.
Note-on
Note-off
Attack
Time
Decay
Time
Start Level
Release Level
Release Time
Attack Level
+99 = approximately 1 octave
–99 = approximately 1 octave
0 = pitch when
key is held
(sustained)
Time
Time-varying pitch settings (when Pitch EG Intensity = +12.00)
Pitch EG change (level) (AMS=JS-Y/Velocity, Intensity= positive (+) value
Note-on
Note-off
Note-on
Note-off
Note-on
Note-off
A note played softly with
Start Level Swing set at 0,
Attack Level Swing set to +,
the Joystick pulled on
A note played strongly with
Start Level Swing set to 0,
Attack Level Swing set to +,
the Joystick pulled on
A note played strongly with
Start Level Swing set to 0,
Attack Level Swing set to –,
the Joystick pulled on
Summary of Contents for microARRANGER
