manualshive.com logo in svg

Komatsu PC500LC-10R, Shop Manual, Page: 4 / 758

Share
Download
Komatsu PC500LC-10R Shop Manual Download Page 4

INDEX

00 INDEX AND FOREWORD ........................................................................................................................ 00-1

ABBREVIATION LIST ............................................................................................................................. 00-6
FOREWORD, SAFETY, BASIC INFORMATION ................................................................................... 00-12

HOW TO READ THE SHOP MANUAL........................................................................................... 00-12
SAFETY NOTICE FOR OPERATION............................................................................................. 00-14
PRECAUTIONS TO PREVENT FIRE............................................................................................. 00-22
ACTIONS IF FIRE OCCURS ......................................................................................................... 00-24
PRECAUTIONS FOR DISPOSING OF WASTE MATERIALS ........................................................ 00-25
PRECAUTIONS FOR HANDLING HYDRAULIC EQUIPMENT ...................................................... 00-26
PRECAUTIONS FOR DISCONNECTION AND CONNECTION OF PIPINGS................................ 00-29
PRECAUTIONS FOR HANDLING ELECTRICAL EQUIPMENT..................................................... 00-35
PRECAUTIONS FOR HANDLING FUEL SYSTEM EQUIPMENT .................................................. 00-37
PRECAUTIONS FOR HANDLING INTAKE SYSTEM EQUIPMENT .............................................. 00-38
PRACTICAL USE OF KOMTRAX .................................................................................................. 00-39
DISCONNECT AND CONNECT PUSH-PULL TYPE COUPLER ................................................... 00-40
PRECAUTIONS FOR DISCONNECTION AND CONNECTION OF CONNECTORS ..................... 00-44
METHOD FOR DISCONNECTING AND CONNECTING DEUTSCH CONNECTOR ..................... 00-48
METHOD FOR DISCONNECTING AND CONNECTING SLIDE LOCK TYPE CONNECTOR ....... 00-49
METHOD FOR DISCONNECTING AND CONNECTING CONNECTOR WITH LOCK TO PULL ... 00-51
METHOD FOR DISCONNECTING AND CONNECTING CONNECTOR WITH LOCK TO PUSH .. 00-52
METHOD FOR DISCONNECTING AND CONNECTING CONNECTOR WITH HOUSING TO ROTATE .

................................................................................................................................................... 00-54

HOW TO READ ELECTRICAL WIRE CODE ................................................................................. 00-55
EXPLANATION OF TERMS FOR MAINTENANCE STANDARD.................................................... 00-59
STANDARD TIGHTENING TORQUE TABLE................................................................................. 00-62
CONVERSION TABLE................................................................................................................... 00-69

01 SPECIFICATIONS .................................................................................................................................... 01-1

CONTENTS ............................................................................................................................................ 01-2
ABBREVIATION LIST ............................................................................................................................. 01-3
SPECIFICATIONS .................................................................................................................................. 01-9

SPECIFICATION DRAWING............................................................................................................ 01-9
WORKING RANGE DRAWINGS ................................................................................................... 01-10
SPECIFICATIONS ..........................................................................................................................01-11
WEIGHT TABLE ............................................................................................................................ 01-14
TABLE OF FUEL, COOLANT, AND LUBRICANTS ........................................................................ 01-16

10 STRUCTURE AND FUNCTION ................................................................................................................ 10-1

CONTENTS ............................................................................................................................................ 10-2
ABBREVIATION LIST ............................................................................................................................. 10-5
BOOT-UP SYSTEM ...............................................................................................................................10-11

LAYOUT DRAWING OF BOOT-UP SYSTEM..................................................................................10-11
SYSTEM OPERATING LAMP SYSTEM ........................................................................................ 10-13
BATTERY DISCONNECT SWITCH ............................................................................................... 10-14

ENGINE SYSTEM ................................................................................................................................ 10-15

LAYOUT DRAWING OF ENGINE SYSTEM................................................................................... 10-15
ENGINE CONTROL SYSTEM ....................................................................................................... 10-17
AUTO-DECELERATION SYSTEM ................................................................................................. 10-20
ENGINE AUTOMATIC WARM-UP SYSTEM .................................................................................. 10-22
OVERHEAT PREVENTION SYSTEM ............................................................................................ 10-24
TURBOCHARGER PROTECTION SYSTEM ................................................................................. 10-26
AUTOMATIC IDLE STOP SYSTEM ............................................................................................... 10-28
COMPONENT PARTS OF ENGINE SYSTEM ............................................................................... 10-31

COOLING SYSTEM.............................................................................................................................. 10-33

LAYOUT DRAWING OF COOLING SYSTEM ................................................................................ 10-33
FAN SPEED CONTROL SYSTEM OF FAN CLUTCH .................................................................... 10-35
ENGINE OUTPUT CONTROL SYSTEM OF FAN CLUTCH........................................................... 10-37
COMPONENT PARTS OF COOLING SYSTEM............................................................................. 10-39

INDEX

00 INDEX AND FOREWORD

00-2

PC500LC-10R

Summary of Contents for PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments